Approvals Agencies and Standards

Underwriters Laboratories, Inc.

Underwriters Laboratories, Inc. (UL) was founded as a non-profit organization that examines and tests products and labels them UL “Recognized” or “Listed” for manufacturers. In the United States UL sets the standard of safety for wire.

UL “AWM” Recognized Components
Many wire and cable products have UL AWM (Appliance Wiring Material) Recognized components styles. A wire or cable product bearing a UL Style can be used for internal and external wiring as a Recognized component of an original equipment product. By using an appropriate UL Recognized component AWM Style product, the manufacturer can then obtain the appropriate UL listing for their product.

UL “Listed” Wire and Cable Products
UL Listed wire and cable products are used in applications where the product is not an integral part of the manufactured system. UL Listed wire and cable products are intended for use within residential, commercial, or industrial buildings. The National Electric Code (NEC®) requires the use of Listed products to meet requirements for various “Articles” within the code.

UL Certification for Canadian Products
Products that meet the requirements of the Canadian Standards Association, but are certified by the Underwriters Laboratories, Inc., are marked with a lower case "c" adjacent to the applicable UL symbol.

Canadian Standards Association

CSA is a non-profit, independent organization that operates a nationally recognized testing laboratory (NRTL) for electrical and electronic materials and equipment.

AWM – Appliance Wiring Material
AWM – Appliance Wiring Material (AWM) is manufactured in accordance with CSA Standard C22.2 No. 210. These products are intended for the internal wiring of electrical and electronic equipment and interconnecting external wiring between equipment.

Definitions:

I=Internal use / II=External Use

A=Not subject to mechanical abuse / B=May be subject to mechanical abuse

1=Wet Location / 2=Oil Resistant

All of these wires and cables must pass one of the following flame tests in order to fully comply with CSA Certification requirements. The following are the most common flame standards:

FT1 – The Vertical Flame Test per CSA C22.2 No. 3
FT1 – The Vertical Flame Test per CSA C22.2 No. 3 which specifies that finished cable shall not propagate a flame or continue to burn after one minute after five, fifteen-second applications of the test flame. There is an interval of fifteen seconds between flame applications.

FT4 – The Vertical Flame Test per CSA C22.2 No. 3
FT4 – The Vertical Flame Test per CSA C22.2 No. 3 for cables in cable trays. This test is similar to but more severe than, the UL Standard 1581 Vertical Tray flame test. The UL 1581 has its burner at 0° from the horizontal while the FT4 has its burner mounted at 20° from the horizontal with its burner parts facing up. The allowable char length is only 1.5m (4.92 ft.) while UL 1581 allows damage up to a maximum of 8 feet.

International Safety Standards Agencies

Most countries have their own standard-writing agencies. However, the basis for the majority of International standards is adaptations from, or exact duplication of, publications from the following Safety Standard Agencies. These Standards Agencies are commissioned to create and publicize International Safety Standards. They are standards-setting agencies only. The enforcement of and testing to these standards is undertaken at the national level, but the final interpretation of design and approval of the product always lies with the National Test Agencies.

European Commission

The European Commission is responsible for determining an overall strategy for implementing European Union (EU) policies and regulations. These regulations are also monitored outside of Europe by the European Commission and EU's diplomatic service, the European External Action Service. They are most commonly known for the CE marking that appears on many products in the European Economic Area (EEA). The marking indicates that the product meets all necessary requirements for being sold in the EEA. It may also be used for products produced in other countries to be sold throughout the EEA without restriction. The main benefit for both businesses and consumers is knowing that the product meets all safety, health, and environmental protection requirements.

IEC (International Electrotechnical Commission)
The IEC is composed of representatives from manufacturers, users, and national testing labs from many of the European industrialized nations. Their primary directive is to publicize recommendations for safety standards. Although IEC publications do not have the force of law, in most cases new standards published by the National Testing Agencies in Europe and Australia have only minor deviations from IEC publications.

CEE (International Commission for Rules for the Approval of Electrical Equipment)
CEE was composed of representatives from European National Testing Labs. The CEE’s work has been taken over by CENELEC.

CENELEC (European Committee for Electrotechnical Standardization)
The primary responsibility of CENELEC is to develop electrotechnical standards which represent a consensus among its European member countries. While IEC publications are generally the basis for European National Standards, CENELEC will cover matters which its members feel are not completely addressed by IEC documents.

National Testing & Approval Agencies

Although a product may have been designed to comply with individual standard agencies, or with IEC, CEE or CENELEC, each product must be tested, approved and marked by the National Testing Agency for each country the cords are to be sold in (such as VDE, SEMKO, DEMKO, etc.) In most cases, it is illegal to sell non-approved products.

Australia – ETSA (Electricity Trust of South Australia)
There are six electrical testing agencies in Australia. Generally, an approval with one of the agencies is accepted by the others. The Standards Association of Australia (SAA) is the recognized association for the preparation of Australian standards. SAA’s policy is to use IEC standards as its guidelines. The SAA mark molded into a plug or connector indicates that a product has been tested and approved by one of the Australian testing agencies and SAA. Australian agencies require that an approval number be molded into the plug and connector. The cordage itself is the same used in Europe-Austria – OVE (Austrian Association for Electrical Technology)

OVE is the standards association and the National Testing Agency, IEC standards are the basis for OVE standards. The OVE mark molded into a plug or connector indicates that a product has been tested and approved for use in Austria.

Belgium – CEBEC (Belgium Electrotechnical Committee)
The recognized association for Belgian standards is the Belgium Electrotechnical Committee (CEB). The range of CEB standards is similar to IEC. The CEBEC mark molded into a plug or connector indicates that a product has been tested and approved by CEBEC for use in Belgium. CEBEC approval is voluntary

Canada -CSA (Canadian Standards Association)
CSA is one of five accredited standards writing organizations in Canada. Unlike other foreign countries, Canada does not have separate standards and national testing agencies. The CSA mark indicates that a product has been tested and approved for use in Canada

United States – UL (Underwriters Laboratories, Inc.)
Underwriters Laboratories, Inc., is charted to establish, maintain, and operate laboratories for the examination and testing of devices, systems and materials to determine their relation to hazards to life and property, and to ascertain, define and publish standards, classifications, and specifications for materials, devices, products, equipment, constructions, methods, and systems affecting such hazards.

Denmark – DEMKO (Danish Electrical Testing Station)
The recognized association for Danish standards is the Danish electrotechnical committee (DEK). DEK adopts CENELEC and IEC standards as their basis for standards. The DEMKO mark molded into a plug or connector indicates that a product has been tested and approved by DEMKO. Goods not bearing this mark cannot be sold in Denmark

Finland – SATIN (Electrical Inspectorate)
The recognized association for Finnish standards is the Finnish Electrotechnical Standards Association (SESKO). Most of the standards set by SESKO are in accordance with IEC and CENELEC publications. The SETI mark molded into a plug or connector indicates that a product has been tested and approved by SESKO and SETI for use in Finland. Use of this mark is mandatory only on equipment used in homes, offices, shops & other premises where the public as admitted.

Germany – VDE (Association of German Electrical Engineers)
The recognized association for German standards is the German Electrotechnical Commission of DIN & VDE (DKE). The DKE standards are identical to IEC standards. The VDE mark indicates that a product has been tested and approved by DKE and VDE.

Italy – IMQ (Italian Institute of the Mark of Quality)
The recognized association for the preparation of Italian standards is the Italian Electrotechnical Committee (CEI). The basis of CEI standards is the IEC and CENELEC standards. The IMQ mark on the plug or connector indicates that a product has been manufactured according to CEI standards. There is no legal authority for the mandatory application of standards in Italy.

Netherlands – KEMA
The recognized association for the standards in the Netherlands is the Netherlands Electrotechnical Committee (NBC). The NEC adopts IEC standards with few deviations. The KEMA mark on the plug or connector indicates that a product has been tested and approved by NEC and KEMA. The use of electrotechnical standards is voluntary in the Netherlands.

Norway – NEMKO (Norwegian Board for Testing and Approval of Electrical Equipment)
The recognized association for Norwegian standards is the Norwegian Electrotechnical Committee (NEK). NEK standards are identical to IEC and CENELEC. The NEMKO mark molded into a plug or connector indicates that a product has been tested and approved by NEMKO.

Sweden – SEMKO (Swedish Institute for Testing and Approval of Electrical Equipment)
The recognized association for Swedish standards is the Swedish Electrical Commission (SEK). There are more than 800 Swedish electrical standards. Most of them are identical to IEC standards. Most of the standards are voluntary, However, domestic electrical equipment is subject to approval and cannot be sold unless approved by SEMKO. The SEMKO mark molded into a plug or connector indicates that a product has been tested and approved by SEMKO.

Switzerland – SEV (Swiss Electrotechnical Association)
The recognized association for Swiss standards is the Swiss Standards Association (SEV). The SEV has adopted IEC standards almost without exception. The SEV mark molded into a plug or connector indicates that a product has been tested and approved for use in Switzerland. All products to be sold in Switzerland must bear this mark.

European agencies require the agency marking to be molded into the plugs and connectors. There are two alternatives for marking cordage, The manufacturer’s name and the National Test Agency symbol are printed on the blue primary conductor. In addition to the primary conductor marking, the symbol for CENELEC—”HAR”—can be printed on the outer jacket. According to CENELEC and the national approval agencies, the “HAR” symbol is not mandatory as long as a National Test Agency symbol is on the cordset. The product is fully approved for use in any Continental European country as long as it is manufactured to CENELEC and foreign agency standards and carries one of the above markings.

 

Need a Quote?

Our quick quote form is an easy way to get you the information you need to keep your project on track.

If you still have questions, chat with us online or call us at 800.633.6339. Our customer service representatives are available to answer questions Monday through Friday, 8am - 5pm CST.

Start Your Quote

Customer Portal | Online Account Management Tool for Current Customers     Log In

Copyright © 2013-2017 Magento, Inc. All rights reserved.